Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Klaster_1

Pages: 1 ... 3 4 [5] 6 7
61
29er / Re: WCB-M-062 reviews
« on: May 07, 2017, 08:46:36 AM »
Quote from: charlesrg on May 05, 2017, 04:58:17 PM
I'm pissed that my bb30 xx1 crankset won't fit my new frame that's bb92.
Long spindle version can be fit to BB92 using RF cinch 30mm BB92 bottom bracket, albeit with some elbow grease. I did that today, but no idea how reliable this setup will turn out. Had to grind down plastic washers a bit, that's the only way to preload bearings and eliminate lateral play. Wheels MFG and RWC seem to offer similar products. I've been running same cranks on a 73mm english threaded bb and Rotor BSA30 cups, thanks to Chinertown too.

62
29er / Re: Klaster_1's Dengfu M06 build
« on: May 05, 2017, 12:11:46 AM »
Quote from: charlesrg on May 04, 2017, 10:20:11 PM
Did you also noticed the rear axle space is out of spec ? Mine is super wide, 146mm instead of the standard 142.
Not sure what you mean. A 142 hub fits nicely, no issue with e-thru axle as well. Did you measure it without wheel?

63
29er / Re: Klaster_1's Dengfu M06 build
« on: May 04, 2017, 09:03:57 PM »
Almost there! When rim tape arrives in a few days, I'll have everything for a draft build. Remaining parts are Darimo bars and Xshifter.

64
29er / Re: Klaster_1's Dengfu M06 build
« on: April 27, 2017, 08:34:11 AM »
Finally sorted out the shock mounts situation. Front Fox pin had to be ground down to 21.5mm, now it fits super snagly. Still waiting for fork and rim tape to arrive. There will be another new weenie part, but let's keep it secret for now ;)



65
29er / Re: Charles M06 XL build
« on: April 26, 2017, 10:57:30 PM »
Quote from: charlesrg on April 26, 2017, 09:20:11 PM
I'm moving the components from my 036 cracked frame.
What happened to your 036 exactly?

66
29er / Re: Frame painting
« on: April 24, 2017, 07:41:28 PM »
Quote from: Patrick C. on April 24, 2017, 07:36:07 PM
If I were going to paint mine I'd want a color, like red- had Peter do mine and it has held up well for almost two years now.
This, most of frame sellers offer a painting service. Go for any color if that's your thing. I own two UD matte frames/rims, all of those look just fine in my book, not a single issue regarding outer layer during last three years.

67
29er / Re: My CS-057
« on: April 21, 2017, 10:31:24 PM »
Quote from: Bradshaw560 on April 21, 2017, 03:36:04 PM
After that I sanded down the red and gray graphics.
How do you go about that? I'm considering to strip my S2200 too.

68
29er / Re: M06 vs 036
« on: April 19, 2017, 09:05:10 PM »
Quote
I know it is 12x142, but is it the same 12x142 rear axle as the 036?
Yes, the frame accepts the same Shimano e-thru axle.
Quote
Do they fit the same tire size?
M06 fits up to 2.3" according to Dengfu. Here's a quote from my thread:
Quote
Tire clearance at widest points, without actual tire: top – 81mm, bottom – 75mm.
Quote
Can you run cables internaly for both the shock and a dropper post on the M06?
Yes, frame has inner guides for both dropper and front shock.

69
29er / Re: Klaster_1's Dengfu M06 build
« on: April 19, 2017, 07:58:46 AM »
A small update to keep thread afloat.

Fox shock mount kit was delivered a couple of weeks ago, too bad seller did not cut it to specified length (21.4) due to "22.2 surely is the width that your frame accepts". Well, that's understandable, my frame has something shady going on for sure, given consistently smooth experience from fellow M06 users regarding eyelet distance. Maybe an early version? Anyway, I'll have to grind it down.

Polymer bushes were too tight too, had to sandpaper outer surface a bit, now pin sits semi-tight. How tight it should be, though? I can rotate it by hand, but not as freely when out of shock eyelet or compared to RWC needle bearing.

Remember one of binding post being too long? I've underestimated how much, at least a couple of mm had to go away.

Also got a pair of black Formula R1R, the build will be sub-10kg after all. The stoppers look great too.

70
29er / Re: Anyone recognize this frame?
« on: March 29, 2017, 08:43:30 AM »
Quote from: Carbon_Dude on March 29, 2017, 06:29:21 AM
Quote from: Klaster_1 on March 28, 2017, 11:34:59 PM
The frame looks like a IP-256, but seattube/toptube junction is different, maybe due to small sizing.

An IP-256 is a hard tail frame, that frame just looks like an IP-036 in a smaller size.  The smaller size doesn't have the gusset between the seat post and top tube.
Just to be clear, I meant whatever you mentioned here. An honest mistake.

71
29er / Re: Anyone recognize this frame?
« on: March 28, 2017, 11:34:59 PM »
The frame looks like a IP-256, but seattube/toptube junction is different, maybe due to small sizing.

72
29er / Re: Klaster_1's Dengfu M06 build
« on: March 22, 2017, 09:25:22 AM »
Quote from: maui400 on March 21, 2017, 01:53:49 PM
I would eloxadize it. Otherwise it might soon start to corrode. Especially in combination with carbon.
A reasonable idea, but lock nut will have contact only with aluminium axle and hanger. I'll see what can be done, mostly because black/red would look better.

By the way, a 22.2mm needle shock mount kit from RWC arrived today. The width was spot-on for rocker arm, inner bearing race does not have any lateral movement when put between eyelets. Using the same method I've checked front eyelet clearance and 22.2 doesn't fit at all, looks like I'll have to order 21.85 or even 21.4 kit. Oh, and rear binding post is officially too long by about 0.7mm, gonna grind it down.

73
29er / Re: Klaster_1's Dengfu M06 build
« on: March 20, 2017, 08:54:10 AM »
Meanwhile, I've got a rear axle lock nut machined by a friendly neightbor, weights 4g. Hopefully it will hold up.

74
29er / Re: Mickes Dengfu M06 build
« on: March 14, 2017, 07:37:02 AM »
So my thru axle has arrived, but without a lock nut. Mikael, did you use nut from other bike? Can you post a photo? I suppose it looks something like this.

75
29er / Re: Mickes Dengfu M06 build
« on: March 13, 2017, 12:07:50 AM »
MickeF, the bike looks awesome. Can't wait enough for my parts to arrive. So in the end, you went with both 22.0 bushings? Did you measure actual eyelets, were they wider or narrower?

Pages: 1 ... 3 4 [5] 6 7