Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Opadeira

Pages: [1] 2
1
I replaced the fender bold at the chainstay/BB junction with a flat head bolt to make it a little easier to get the wheel on and off.

I designed a screw for 3D printing that fits flush with the frame:
https://www.thingiverse.com/thing:6266960


2
My wheel rim has an internal width of 22mm. However, the tire tread rubs against the rear chainstay of the frame. To resolve this, I applied a layer of transparent TPU protective film to the frame. The front fork does not need to worry about the same problem
I also have 50c Rambler tires, but I haven't installed them on the CFR707 yet. When I previously mounted the Rambler tires on the same wheelset, their actual width measured 47mm, slightly narrower than the current Rac King's 49mm. Additionally, the tread was less pronounced and easier to manage. Therefore, I don't think you need to worry about the width issue.

can anyone else report on the tire clearance? I was planning to buy Continental Race Kings 2.0 but am hesistant now after reading this. Carbonda lists the tire clearance at 50mm, so theoretically they should fit.

3
I ran full housing for the rear derailleur past the bottom bracket and out the chainstay. For the front derailleur, I ran the housing to the stopper in that little rectangular plastic piece under the bottom bracket and then just the inner to the derailleur. I  used a bit of the plastic guide that came with the frame to line the last little bit of the cable and hopefully keep dirt off.

Shifting has been good after getting it dialed in. The tension in the front derailleur cable holds that plastic part in, so I couldn't pull it out for the picture without having to loosen the cable at the derailleur.

I'm glad I opened it up for the picture. It looks like once of the inserts for the cover bolts is corroding so I will have to grease it really good.

I contacted Carbonda and this is the "official" way to do it. Just for the record :). I decided to run full cable housing to the front mech tough as it was stated to do this in the Shimano GRX manual. This way the cable is also protected from dirt that will come off the tire at this location.

4
I ran full housing for the rear derailleur past the bottom bracket and out the chainstay. For the front derailleur, I ran the housing to the stopper in that little rectangular plastic piece under the bottom bracket and then just the inner to the derailleur. I  used a bit of the plastic guide that came with the frame to line the last little bit of the cable and hopefully keep dirt off.

Shifting has been good after getting it dialed in. The tension in the front derailleur cable holds that plastic part in, so I couldn't pull it out for the picture without having to loosen the cable at the derailleur.

I'm glad I opened it up for the picture. It looks like once of the inserts for the cover bolts is corroding so I will have to grease it really good.

thank you!
My misunderstanding was that the cable goes into the plastic without an endcap. I was looking for a port that fits a housing endcap.

5
External routing - the cable housing for derailleur shifting only go up to the cable stopper on the down tube.

That's the thing, there are no cable stoppers on the down tube on the 707. Just inserts that let a cable housing pass through. It would be a clear "housing all the way" situation if not for the sliding plate for the inner cable i posted a picture of before.

6
Does the 707 have proper eyelets for full lenght mudguards? I'm contemplating between a 696 or 707 frameset for a commuter that I will use in rain and snowy winter conditions.

There's one mount at the bottom bracket. A bolt on adaptor to provide two mounts on the seat stays and two mounting points at the dropouts, so yeah I'd say it's compatible with full length mudguards

7
Hello, I believe that the cable housing should always pass through the frame, regardless of whether it is a fully internal or semi-internal routing frame. I hope this helps you.

are you sure? I just got the chance to open up the frame at the bottom bracket and it very much looks like the cable is supposed to run without housing in the frame. See photo. I just dont get where the upper endstop is supposed to be, the ports into the frame dont seem to support a cable housing endstop.

Can anyone maybe share a picture of how they wired up their front derailleur?

8
regarding shifter cable routing (external routing):
Can someone please clarify for me if the cable housing should be routed all the way through the frame or is the part inside the frame without a housing?

9
The CFR707 can use an integrated handlebar and stem with internal routing or a conventional separate bar and stem. I set mine up with a standard handlebar and stem, so mounting accessories is no problem. I went with external routing to make the build and cockpit changes easier.


For sizing, it's worth comparing the CFR707 with your bikes in geometrygeeks, or by making your own spreadsheet. I used the stack, reach, and stem measurements from my road bike to determine which size CFR707 frame to buy. The XL frame has roughly the same stack as my road bike but a longer reach. I compensated with a shorter stem to get the bars where I want them. I could have made a L work, but sizing up moves the front wheel farther ahead. This makes the bike more stable and prevents toe overlap, even with 700x50mm tires. I'm 190 cm.

what's your inseam measurement? I'm about the same height

10
digging up this thread because I'm looking for the same thing.
Anyone know something. >20° flare is just too extreme for me

11
Could any of the CFR707 owners check the frame clearance for a Stages Power Meter on their bike for me?

https://support.stagescycling.com/en/support/solutions/articles/1000137517-how-can-i-find-out-if-my-bicycle-is-compatible-with-a-stages-power-meter-
 

12
Cyclocross Frames, Wheels & Components / Re: Carbonda CWRD44C Rim
« on: April 14, 2023, 08:25:28 AM »
Anyone got experience/info on this wheelset or the rims? Considering getting the rims together with a CFR707.
They seem pretty similar to BTLOS GX45A https://btlos.com/gravel-40-50mm-depth-carbon-wheels/asymmetric-45mm-depth-29mm-external-width-clincher-gravel-cx-disc-brake-carbon-rims

13
29er / Re: FM1001 / FM1156 - 135mm frame
« on: February 22, 2021, 03:34:23 AM »
Leverage Ratio of the FM1001.
Source: Adam

14
29er / Re: Carbonda fm936 Thoughts
« on: May 07, 2020, 05:47:13 AM »
what type of derailleur hanger does the frame use? Is one that's easy to replace through online bike shops or should I order spare ones from Carbonda?

15
29er / Re: Carbonda fm936 Thoughts
« on: April 03, 2020, 01:54:50 AM »
Not sure if sarcasm?  I'm asking here in hopes of getting community feedback from people that have hands on experience with the frame.  I also find it easier avoiding the language barrier and time difference for more technical questions.  This will be my third frame from Carbonda and have had zero issues with them.

No, not sarcasm. I just think it's a good sign that Carbonda is taking care of such issues as yours. It's valuable information to me that you posted your experience.

Pages: [1] 2