31
29er / Re: Ip256sl building in progress
« on: November 30, 2014, 07:58:37 AM »
Mtb2223: how long is the cable stop inside? I think i'm through with a 4mm drill, but almost the entire drill was needed
Chinese Carbon MTB Forums
News:
Happy Holidays!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
29er / Re: IP-256SL XC Racer Build 18.5lb
« on: November 29, 2014, 06:00:17 AM »
Can you tel me how you did the cable drilling for the RD?
33
29er / Re: Ip256sl building in progress
« on: November 29, 2014, 05:56:52 AM »
I think its the best solution, but a hel of à job! Stil drilling.....
34
29er / Re: Ip256sl building in progress
« on: November 28, 2014, 12:56:44 PM »
Blisters on my fingers.... You dit it with a dremel or by hand also?
35
29er / Re: IP-256SL XC Racer Build 18.5lb
« on: November 28, 2014, 10:41:02 AM »
Looks great! Interested in how your drilling of the rear cablestopt was
36
29er / Re: Ip256sl building in progress
« on: November 28, 2014, 10:33:13 AM »
I Will bleef the brake tomorrow. I'm now at the point of drilling the cablestopt out. Can somebody tell me how the %#$£$% i can drill the rear stop?
37
29er / Re: Ip256sl building in progress
« on: November 26, 2014, 02:27:44 PM »
Got my iplay toys today! Just finished the break install so its time for some pics. Rear break cable was a bit time consuming, but at the end i managed to instal the brake whithout bleeding.
39
29er / Re: Ip256sl building in progress
« on: November 24, 2014, 03:25:23 PM »
I'm up to the point if choosing my shiftercable...... Harder than i thougt! I'm considdering, sram, sram slickwire, Jagwire. Does anyone have good experiences with any of them?
40
29er / Re: Ip256sl building in progress
« on: November 21, 2014, 04:30:18 PM »
Thanks man, can't wait to ride it! I don't have the reinforced RaRa's. In the meanwhile i take a good look at your build 
41
29er / Re: Ip256sl building in progress
« on: November 21, 2014, 11:07:16 AM »
Completed my build list today. Hope to stay under 9kg
Not sure about keeping my Prologo Saddle and my look paddles.
The frame has left Hong Kong at the beginning of last week, so i hope it arrives soon! Any experiences in the shipping times to europe/Holland?
Not sure about keeping my Prologo Saddle and my look paddles.
The frame has left Hong Kong at the beginning of last week, so i hope it arrives soon! Any experiences in the shipping times to europe/Holland?
42
29er / Re: IP-256SL XC Racer Build 18.5lb
« on: November 19, 2014, 03:57:19 PM »
Have an almost identical build, except for the wheels. Looking forward to the next pics. What are your plans with the RD cable? Are you going to run the full outer cable through the frame?
43
29er / Re: Dutch ip-256sl build
« on: November 08, 2014, 01:32:17 PM »
Oké now i get it, thanks! Im still not sure rather i'll run the bare cable or drill out the stops. Guess i have à few weeks to decide. Maybe i'll need your experience by that time ;-)
44
29er / Re: Dutch ip-256sl build
« on: November 08, 2014, 01:05:33 PM »
I meant the frame seems to be delivered with different inner tubes. (With or without) when running bare cables through the frame, i would prefer to have inner tubes. The angle the cable has to make on the guide sleeves of the BB seems quite unnatural witch could effect the shifting.
45
29er / Re: Dutch ip-256sl build
« on: November 08, 2014, 12:47:29 PM »
Strange: apperently xmiplay had two different styles of frames. Is there à possibility of running the full outer cable trough the frame. And how is the shifting with the bare cables through the frame?