Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ENEP

Pages: [1] 2 3 ... 9
1
Road Bike Frames, Wheels & Components / Re: Searching a lightweight thru axle
« on: May 01, 2024, 02:10:16 AM »
Over Fast

https://www.pandapodium.cc/product/overfast-ultralight-thru-axles/

2
Cyclocross Frames, Wheels & Components / Re: 3 years warranty Carbon Speed Gravel frameset
« on: April 30, 2024, 01:02:35 PM »
Familiar design  ;)

3
Cyclocross Frames, Wheels & Components / Re: ENEP's YishunBike G095-D build thread
« on: April 30, 2024, 12:53:15 AM »
Quote from: Hmpf on April 29, 2024, 01:07:10 PM
That looks really fast! (And the wheels look far too narrow for the frame :D)

For me, the air does not hold as well as in the butyl tubes.
I run 35mm with 3.5 bar, after a week it's still 1.5 bar.

I had the 28s from another bike so used them. Will most likely upgrade to better tires and 32mm.
But, they will most likely look to narrow for the frame anyway as the frame takes 700x50.

Received the wheels a month ago, mounted tape, tubes and tires directly. Pumped up to ~4.7 bar.
Yesterday, before the first ride there was 3.5 bar left in the tires. So 1 bar pressure loss over a month hanging in the garage.

4
Cyclocross Frames, Wheels & Components / Re: ENEP's YishunBike G095-D build thread
« on: April 28, 2024, 03:16:27 PM »
Quote from: this is dog on April 28, 2024, 12:00:45 PM
Nice looking rig! Do those TPU tubes hold air well?

Thanks!

No issues with loss of air pressure with the tpu tubes so far. But haven’t ridden much yet so maybe too early to say.

5
Cyclocross Frames, Wheels & Components / Re: ENEP's YishunBike G095-D build thread
« on: April 28, 2024, 08:49:48 AM »
Had a minor surgery, few weeks of recovery and then a couple rounds of the flu.

However today was the day for the first shake down after build. Complete with a set of Elite ENT 50mm (pillar wing upgrade) equipped with 28mm Schwalbe One and RideNow TPU-tubes.

The bike is fast, smooth and comfy. No complaints for the moment.

6
Cyclocross Frames, Wheels & Components / Re: Cyclocross frame
« on: March 26, 2024, 02:48:14 AM »

https://chinertown.com/index.php/topic,4374.0.html


7
Road Bike Frames, Wheels & Components / Re: Puncture proof Continental Gatorskin tyres any good?
« on: March 21, 2024, 04:22:49 AM »
Quote from: Froglover825 on March 20, 2024, 07:25:58 PM
Who in their right mind would go with the gatorskin unless you know nothing about cycling?
I run GP5k's and haven't had a puncture in over 2 years now, that's with riding a good 30,000km over shitty Australian roads.

What's your setup? Tubeless? If tubes, which kind butyl/latex/tpu?

8
Road Bike Frames, Wheels & Components / Re: More Aero frame in direction of Merida Reacto?
« on: March 08, 2024, 07:22:34 AM »
https://www.speedercycling.com/Carbon-Integrated-Road-Disc-Frameset-SC-R49D-_p399.html

https://www.sp-cycle.com/spcycle-2024-new-aero-carbon-road-bike-frame-disc-brake-full-hidden-cable-700x32c-race-bicycle-carbon-frameset-p5517135.html

Also Workswell.

Most frame manufacturers have an aero frame in their range.

9
Road Bike Frames, Wheels & Components / Re: Yuanan Carbon fiber wheelsets Year end discount promotion
« on: March 06, 2024, 06:45:32 AM »
The YAG35 rim is the same as used for Elite wheels Marvel gravel wheel set.

https://www.elite-wheels.com/wp-content/uploads/2023/02/2023-Elitewheels-Dealer-Brochure.pdf
See PDF page 18 for spec.

Buying from Yuanan directly you can customize the wheels spec with your choice of hub and spokes.


10
Component Deals & Selection / Re: chinese rear gravel derailleur compatibility
« on: March 04, 2024, 08:38:16 AM »
Quote from: raisinberry777 on February 26, 2024, 05:46:38 AM
You can make this mod to the GRX 11s derailleur by using an XT cage to make it shift an 11-51 Shimano 11s MTB cassette:


Code: [Select]
https://www.youtube.com/watch?v=ynpFsE8snww

11
Road Bike Frames, Wheels & Components / Re: All Road / Endurance build
« on: March 04, 2024, 08:04:58 AM »
You've added Carbonda CFT896 to your comparison. Here you go with CFR696:
https://geometrygeeks.bike/compare/carbonda-cfr696-2020-560,carbonda-cfr696-2020-580,bmc-roadmachine-02-two-2019-56,ican-graro-2024-56,storck-fenomalist-2012-55/

Never rely on producers naming of sizes, always look at the geo tabel and compare measurements to find the right size :)


12
Road Bike Frames, Wheels & Components / Re: All Road / Endurance build
« on: March 04, 2024, 12:42:01 AM »
Big positive with many gravel frames for commuting is dedicated fender mounts. Personally I would never commute without fenders and fenders mounted to a frame with dedicated mounts are superior. Would also choose a frame with externally routed cables for ease of service.

The classic and trusty Carbonda CFR696 would be a great option. Should have enough space for studded tires, fenders and room for mud/snow clearance without clogging up. https://www.carbonda.com/road/gravel/80.html

13
Cyclocross Frames, Wheels & Components / Re: Yishunbike G095D (Speed Gravel)
« on: March 01, 2024, 05:06:31 AM »
Does anybody have information om maximum chain ring size if running a 1x-setup?

14
Component Deals & Selection / Re: L-Twoo, Sensah or 105?
« on: March 01, 2024, 04:32:47 AM »
Quote from: brifter5 on February 28, 2024, 09:37:58 PM
I would look into some kind of shimano grx setup , 1x , 11-51T cassette seems appealing to me.

I'm also interested in this frankenstein setup on my gravel/road bike. Which parts and chainring size are you looking in to?

15
Road Bike Frames, Wheels & Components / Re: TideaceBike New mold Road Frame FM-CR068 groupbuy
« on: March 01, 2024, 03:17:56 AM »
Would be interesting to see a geometry chart and real life photos of frame when available.

Pages: [1] 2 3 ... 9