Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - turboenterprise

Pages: 1 ... 5 6 [7]
91
29er / Re: IP-057 Full Build - Need Advice
« on: May 28, 2014, 09:39:24 PM »
Anyone else looking for forks.  It has been slim pickens for Reba RL's for sale.  There is a lot more Fox' CTD for sale.  Reba's are bit harder to find in 15mm axles too.  This one used SID caught my eye though but not tapered. http://www.ebay.com/itm/100mm-29-Sid-Rock-Shox-15mm-thru-axel-/151313722718?pt=US_Forks&hash=item233b002d5e

92
29er / Re: My FM-057 Build Thread.
« on: May 26, 2014, 12:36:50 PM »
Quote from: Carbon_Dude on April 28, 2014, 12:55:49 PM
A little different than for a SRAM GXP bottom bracket on my XX1 setup.  Per SRAM's installation instructions:

Use calipers to measure the bottom bracket shell width of your frame.
  • 68 mm bottom bracket shells require one 2.5 mm spacer on each side of the bottom bracket shell.
  • 73 mm bottom bracket shells do not require spacers.

Carbon what did the IP-057 have ? 68mm with spacer or 73mm with none?

93
29er / Re: IP-057 Full Build - Need Advice
« on: May 24, 2014, 10:00:32 AM »
Thanks Carbon_Dude
3.Is there a conservative way to know what length stem you need? I run (1-1/8 x 0-Degree x 70mm, Black) with a riser bar right now on another bike.
4. Yes the Q168 I forgot to type it
7. Whats the part number/item number for the 180mm spacer?

I have a torque wrench, carbon paste, grease, and repair stand.  Going to have to do the homemade press for headset. Not sure what else. Any tips or links?

94
29er / Re: IP-057 Full Build - Need Advice
« on: May 23, 2014, 06:25:57 PM »
Ok here is a build list: Thoughts / What's missing? any adaptors? cables?

P-057 in 15.5'' with BSA in UD matt for 142x12 -  400 USD/piece
Fitting NECO headset - 15 USD/ set
Fitting seat post IP-SP7 in UD matt - 40 USD/piece
Carbon saddle IP-SD1  in UD matt - 55 USD/piece
700mm Riser Carbon handlebar IP-B05 in UD matt-  38/USD
Seatpost clamp - $0
Fitting front 15mm axle and rear 12mm axles are 35 USD/pair
Extra rear derailleur hanger right part - 15 USD/piece
N-SS IP-HR930C 30mm hookless wheels - 585 USD/pair
N-SS: Novatec D771/D772 hubs for 100x15/142x12 for SRAM XX1, Sapim CX-Delta Spokes, Sapim nipples
or DTSwiss 350 ???USD/pair
Maxxis Ignitor - $47/USD a piece
RockShox Reba RLT Solo Air 100 29in Suspension Fork 15mm Maxle Remote Tapered -$4xx/USD
XX1,175m,GXP,32T - 9xx/USD
Ergon Race Grips - $0- take off other
SHIMANO DEORE XT BL-M785 BR-M785 Hydraulic Disc Brakeset 850/1400 160mm -$200/USD
SHIMANO XT 160mm Centerlock Rotor SM-RT81-S Ice Technologies Disc Brake Bike - $70/USD pair
Eggbeater 3 Pedals - $72.50 USD


95
29er / Re: IP-057 Full Build - Need Advice
« on: May 20, 2014, 09:32:37 PM »
What you do think? Its been cut to 7inches.  Enough?

http://www.ebay.com/itm/2014-Rock-Shox-Reba-RL-29er-100mm-Solo-Air-15mm-Maxle-Tapered-Steertube-/251530262911?pt=US_Forks&hash=item3a905f397f


96
29er / Re: IP-057 Full Build - Need Advice
« on: May 19, 2014, 07:42:51 PM »
Thanks for the help.  I appreciate the advise. 

97
29er / Re: IP-057 Full Build - Need Advice
« on: May 19, 2014, 07:09:34 PM »
I asked lightbicycle if they can sell those hubs but it appears they don't.  http://www.light-bicycle.com/the-more-detail-about-hubs-MTB-hub-and-road-hub.html

Out of the hubs listed which is most equivalent.  I don't know a wheel builder and I am looking for as most turn key as I can get building my own bike.  If it really warrants it then wheel builder it is but I am clueless on it.   

98
29er / IP-057 Full Build - Need Advice
« on: May 18, 2014, 09:46:23 PM »
I'm looking to build a IP-057 and need some help.  This is my first full build and I need some advise on what parts to add.

Ip-057

Question on what to get:
Headset - use XMI or Cane Creek?
Fork - not sure what size 1-1/8?
               - recommendations?

XX1 - Group Set
   
Wheels - Light Bicycle all mountain


          - Pillar Aero X-TRA 1420 - spokes
          - 28h or 32h - which one?
          - Hub which one to match - Are these the right ones?
                        - Do you need an adaptor?
Hope Pro 2 hub Front
Hope Pro 2 hub Rear


Update:
Build List
https://docs.google.com/spreadsheets/d/1eMRzZQpDnofHlpCb8DAsYLKIf2MUE0tY3iZiCT6dvmU/edit?usp=sharing

Build notes
https://docs.google.com/document/d/1bKzEmsKo2kkaUO0hJBv8vUSjgSh-j89bTXlNHX7fHfs/edit?usp=sharing

Update:
Been racing and riding now for a couple months.  Peter at XMIplay is awesome to deal with.  Quality has been great.  Any issues Peter has taken care of it.  Buy with confidence from XMIplay

Pages: 1 ... 5 6 [7]