Tideace NEW Gravel Frame: GR201

[darario]

The rated capacity of a powerbank refers to the rated voltage of 3.7V of a lithium cell of a powerbank. Means that a 3S battery with 11.1V rated power can store the same energy with ⅓ of the rated capacity.

10,000 mAh * 3,7 V ~ 37 Wh
3,333 mAh * 11.1 V ~ 37 Wh

[XXenzuXX]

The rated capacity of a powerbank refers to the rated voltage of 3.7V of a lithium cell of a powerbank. Means that a 3S battery with 11.1V rated power can store the same energy with ⅓ of the rated capacity.

10,000 mAh * 3,7 V ~ 37 Wh
3,333 mAh * 11.1 V ~ 37 Wh

Thanks for your explanation, I overlooked that. You're right, of course.

[Raficheq]

How many mounting holes are there in the frame?
What should be used to cover them? What will be the lightest?
Do you have any reliable links?

[Uberflo]

You can use M5 nylon screws from AliX

[Kme]

My build is complete.
Detailed adjustments remain, but I can ride now.

[armada]

My build is complete.
Detailed adjustments remain, but I can ride now.

dh mallets on Gravel?

[Kme]

dh mallets on Gravel?

It's actually mallet E and it works pretty well on the single trail.

[wolfi]

Hi,

I have a question to the geometry (sorry, if this has been already asked, didn't read the full 65 pages):

According to the geo table, the frame in size 560 has a 145mm steerer tube and fork length 400mm. The HP says "support suspension fork", normally the gravel suspension forks are 425mm length.

This would mean, that the front will be relatively low, if it runs with a rigid fork, needing 2,5 cm more spacers.

Can anyone enlight me on this topic, or anybody having problems with the low front?

Thanks
Wolfgang

[Wouter]

I have the Lexon Unox bar on my gr201, when I stand on the padels and put down power the headset/ cockpit creaks. Could it be that the metal sleeve the Lexon Unox comes with isnt the snuggest fit and that I because of that my cockpit and headset not totally play-free get? Somebody else that also has this problem? Any solutions?

[pieterjnz]

I have the Lexon Unox bar on my gr201, when I stand on the padels and put down power the headset/ cockpit creaks. Could it be that the metal sleeve the Lexon Unox comes with isnt the snuggest fit and that I because of that my cockpit and headset not totally play-free get? Somebody else that also has this problem? Any solutions?

I have the bar that ships with the frame from Tanatan. Had a similar problem.

Turned out it wasn't the bar. The rear dropout wasn't faced properly and thus not perfectly flat so under pressure when standing out of the saddle the wheel had micro movements and the sound carried through the frame so sounded like it came from the cockpit. I just faced the rear dropout carefully to removed minimal material and that solved my problem.

Might not be the same for you, bottom line is that sounds are deceiving and could carry through the frame so check everything.

[Wouter]

I have the bar that ships with the frame from Tanatan. Had a similar problem.

Turned out it wasn't the bar. The rear dropout wasn't faced properly and thus not perfectly flat so under pressure when standing out of the saddle the wheel had micro movements and the sound carried through the frame so sounded like it came from the cockpit. I just faced the rear dropout carefully to removed minimal material and that solved my problem.

Might not be the same for you, bottom line is that sounds are deceiving and could carry through the frame so check everything.

I faced the breakmounts, no disc rubbing when standing on the pedals. I can also get the sound when I push the bars into the ground when standing still..

[pieterjnz]

I faced the breakmounts, no disc rubbing when standing on the pedals. I can also get the sound when I push the bars into the ground when standing still..

Just to clarify. Mine was not the Break Mounts, it was the dropouts where the hub makes contact with the frame.

[Wouter]

Just to clarify. Mine was not the Break Mounts, it was the dropouts where the hub makes contact with the frame.

Oh okay, sorry. Going to check it!

[pieterjnz]

Oh okay, sorry. Going to check it!

It was my left rear that was uneven and then down pressure on the bike as the bike moved side to side would cause micro movement at the hub which then carried through the frame and sounded like it was the cockpit. I was quite surprised because I didn't expect the problem to be all the way at the back wheel

[Wouter]

Look like I got quite a big gap between frame and fork on my gr201 (using kugellager bearings and lexon unox handlebar). If i watch others with this combination they have a lot less room between fork and frame. I have some creaks when im out of the saddle, maybe this is also a reason?