Spcycle R065 700C Full Carbon AERO Road Disc Brake Frameset

[fhill]

Has anyone tried a magene pes 505 on this frame? Does it fit?

Looking at the shape of the drive side of the frame would give me hope, the threaded area is a good piece "higher" than the frame so the P505 should work with that

[Jimmytheking]

My build is complete. Final weight - 17.6 pounds (size large) without pedals. Of course it is raining here today so maybe tomorrow will be the test ride.

[william95]

Hi everyone,
do you have any pictures of your battery setup for the Shimano Di2 Ultegra groupset? Thanks!

[jordanc1010]

The battery goes in the downtube similar to some canyon bikes.

[Tilmanstoa5ty]

I just finished my build and took it for a test drive. Unfortunately I have found a few issues. All at the front end. The fork has a little bit of movement where the fork meets the frame there is also some movement and noise coming from where the wheel meets the frame but i think this issue is coming from the tagoola wheels, both are large issues and makes it feel quite unsafe to ride. I have just contacted both companies, i will send an update when i get a response.

Are you 100% sure that it's correctly installed? Is there enough gap between topcap and compression plug? Did you apply enough preload on the topcap?

[jordanc1010]

It was not installed correctly, problem solved.

[william95]

Hi everyone, I'm almost done with the assembly, but there's a 1 mm play in the fork and I can't seem to fix the problem. I've attached a few photos of the setup—can anyone tell me if I'm making a mistake somewhere? Thanks a lot!

https://ibb.co/4nRXDkSb
https://ibb.co/G443hJgh
https://ibb.co/nqXpFw97
https://ibb.co/zTmMGxKn
https://ibb.co/j9c5fKBq
https://ibb.co/5WDFMwpS
thanks

[getmekd]

Hi everyone, I'm almost done with the assembly, but there's a 1 mm play in the fork and I can't seem to fix the problem. I've attached a few photos of the setup—can anyone tell me if I'm making a mistake somewhere? Thanks a lot!

https://ibb.co/4nRXDkSb
https://ibb.co/G443hJgh
https://ibb.co/nqXpFw97
https://ibb.co/zTmMGxKn
https://ibb.co/j9c5fKBq
https://ibb.co/5WDFMwpS
thanks

It seems like you dont have any gap between the frame and your bottom cover, spacer whatever its called.
https://ibb.co/bMwN4H9x

To preload the bearings you need a gap there, you can try sanding the bottom part of the cover a bit and try again

[Dr J]

Hi everyone, I'm almost done with the assembly, but there's a 1 mm play in the fork and I can't seem to fix the problem. I've attached a few photos of the setup—can anyone tell me if I'm making a mistake somewhere? Thanks a lot!

https://ibb.co/4nRXDkSb
https://ibb.co/G443hJgh
https://ibb.co/nqXpFw97
https://ibb.co/zTmMGxKn
https://ibb.co/j9c5fKBq
https://ibb.co/5WDFMwpS
thanks

my bad! I had misinterpreted the picture!

[getmekd]

your fork still seems too long. Need to cut it shorter

No its not, its even cut too much, but shouldnt be problem for preloading
https://ibb.co/xKtWWKY1

[william95]

yes I cut another piece because I thought there was not enough space between the top and the cut to do compression, but even cutting it back did not solve my problem

[william95]

Did I put the pieces together the right way? Is something missing?

[Uberflo]

C ring which guides the cables into the frame is often a problem (if metal out of tolerance). Did you check that?

[william95]

I have doubts about this part, but I don't see how to check if it is OK. I inserted it as it seemed good to me, but I don't know if this part has a defect.

[Uberflo]

If you push the c ring into the fork and it moves front to back without preload than the c ring is out of tolerance. The plastic c rings work better because they can slightly adapt due to the material.