SPCycle G028 new gravel frame with 57mm tires clearance

Started by CycOps, April 26, 2026, 06:54:50 AM

Previous topic - Next topic

victorjc7

Hi everyone!

I've purchased an SP-Cycle G028 frame and I'm planning to build it with a Shimano Ultegra Di2 R8170 12-speed groupset.

I'd like to keep my existing Shimano Ultegra FC-R8100 road crankset, but I've been discussing crankset compatibility with SP-Cycle and there's a potential clearance issue.

This is what the manufacturer told me:

We tried installing 50-34T Shimano Road cranks, but the chainrings would hit the chainstays. The small chainring is making contact with the chainstay. I think a 3mm spacer needs to be added to the drive side.

They also explained that the difference between Shimano Ultegra road and GRX cranksets is approximately 3mm in both chainline and Q-factor:

Ultegra: 44.5mm chainline / 148mm Q-factor.

GRX: 47mm chainline / 151mm Q-factor.

However, they haven't tested the suggested 3mm spacer, so this is only a theoretical solution at this point.

My questions

  • Has anyone successfully installed Shimano Ultegra R8100, 105 R7100 or other Shimano road 2x cranksets on the SP-Cycle G028?
  • Has anyone experienced inner chainring-to-chainstay clearance issues?
  • Would a 3mm drive-side spacer solve this problem? If so, where exactly should it be installed?
  • Would using a smaller chainring combination, such as 46/36T, help? Or is the issue mainly related to the crankset chainline?
  • Which T47 bottom bracket would you recommend for Shimano 24mm Hollowtech II road cranks on this frame?

jn46

No direct experience but you'd want to put the 3mm spacer on the drive side of the axle before you insert the chainset. You might want to run some more pedal washers on non drive side to balance out your stance.

This is assuming the Ultegra axle is long enough to allow the 3mm spacer and still provide adequate length to attach left crank arm.

You'll likely need to use a GRX front mech too, as the uletgra one will struggle with the additional outboard movement.

Seems like a  headache just to keep the chainset

victorjc7

Quote from: jn46 on <strong>Today</strong> at 06:38:43 AMNo direct experience but you'd want to put the 3mm spacer on the drive side of the axle before you insert the chainset. You might want to run some more pedal washers on non drive side to balance out your stance.

This is assuming the Ultegra axle is long enough to allow the 3mm spacer and still provide adequate length to attach left crank arm.

You'll likely need to use a GRX front mech too, as the uletgra one will struggle with the additional outboard movement.

Seems like a  headache just to keep the chainset

Thanks for your advice!

Keeping the Ultegra crankset isn't important to me. My main priority is keeping the Ultegra Di2 2x12 electronic shifting system.

I'd prefer to avoid Shimano GRX cranksets, as I don't really like their aesthetics.

Could you recommend any specific crankset models or brands that would fit the SP-Cycle G028 and work with my Ultegra Di2 groupset?Ideally, I'd like to keep my Ultegra front derailleur too, but I'm open to replacing it if necessary.

This is my first bike build, so I'm still a bit lost with compatibility. Any help would be greatly appreciated!

jn46

Try the 3mm spacer option and it might work out.

Have a look at some of the cheaper carbon titaniun 24mm axle cranksets like the Rpantahi. This has a longer 99mm axle compared to the Ultegra so gives you more adjustment room. Will drop about 150g in weight too.

Vaclav

I have a G028 with a ThinkRider PP5 with 1st-generation Goldix road crankset and 148 mm Q-factor. I'm using FC-R8100 chainrings (46/36), and I also have a 50/34 setup.

I added a 1 mm spacer on the drive side to get enough clearance for the small chainring. I also added a 1 mm spacer on the non-drive side to keep the crank arms equally spaced and avoid having to adjust my cleats.

However, be careful: these cranks have a fairly long spindle section for mounting the non-drive-side crank arm. With an original Shimano crankset, the crank arm might not reach far enough to engage the safety pin properly.