Mondince FM376 - 57mm tire clearance

Started by Hazardman_69, August 11, 2026, 01:48:24 PM

Previous topic - Next topic

daaaaaaaaaa

You cannot view this attachment.
  • Frame: Mondince FM376, size M, UD matte
  • Cockpit: Winspace Adventure Aero, 380 × 105 mm, 12° flare
  • Seatpost: Mondince carbon 27.2 mm, 0 mm setback
  • Saddle: Prologo Scratch M5
  • Shift/brake levers: SRAM Rival E1 AXS
  • Rear derailleur: SRAM Force XPLR E1 AXS, Full Mount
  • Cassette: SRAM Force XPLR 10–46, 13-speed
  • Crankset: SRAM Force E1, 165 mm, DUB Wide, with power meter
  • Chainring: Garbaruk Aero 40T
  • Brake calipers: SRAM Rival E1, flat mount
  • Rotors: SRAM CLX-R Centerlock, 160 mm front / 140 mm rear
  • Wheelset: BTLOS WRMC64 carbon, 32 mm internal, 64 mm deep, hooked, GravelXpert hubs, Sapim CX-Ray spokes
  • Tires: Pirelli Scorpion XC RH 29 × 2.40 LITE TLR, tubeless
  • Weight: 8.7 kg (incl. pedals, bottle cages and Garmin mount)

this is dog

Quote from: daaaaaaaaaa on November 20, 2026, 07:16:23 AMYou cannot view this attachment.
  • Frame: Mondince FM376, size M, UD matte
  • Cockpit: Winspace Adventure Aero, 380 × 105 mm, 12° flare
  • Seatpost: Mondince carbon 27.2 mm, 0 mm setback
  • Saddle: Prologo Scratch M5
  • Shift/brake levers: SRAM Rival E1 AXS
  • Rear derailleur: SRAM Force XPLR E1 AXS, Full Mount
  • Cassette: SRAM Force XPLR 10–46, 13-speed
  • Crankset: SRAM Force E1, 165 mm, DUB Wide, with power meter
  • Chainring: Garbaruk Aero 40T
  • Brake calipers: SRAM Rival E1, flat mount
  • Rotors: SRAM CLX-R Centerlock, 160 mm front / 140 mm rear
  • Wheelset: BTLOS WRMC64 carbon, 32 mm internal, 64 mm deep, hooked, GravelXpert hubs, Sapim CX-Ray spokes
  • Tires: Pirelli Scorpion XC RH 29 × 2.40 LITE TLR, tubeless
  • Weight: 8.7 kg (incl. pedals, bottle cages and Garmin mount)

Sweet looking build!

Serva86

Has anyone built up this frame (FM376 GR257...) with a front derailleur and a GRX 48-31 double crankset?

kyleclarkson07

Has anyone found plugs that fit better for the various fork/frame bosses than the one Jack supplied? I've had a few of the supplied ones fall out on rides, so far I've ordered two different sets of replacements but both were undersized

hubba

Quote from: kyleclarkson07 on <strong>Today</strong> at 08:29:21 AMHas anyone found plugs that fit better for the various fork/frame bosses than the one Jack supplied? I've had a few of the supplied ones fall out on rides, so far I've ordered two different sets of replacements but both were undersized

I'm using some rubber plugs from Aliexpress. They are a bit oversized so I had to cut the end smaller and then twist them in they seems to be pretty tight but I haven't completed the build yet. I used 6mm ones from the link 4mm is too small 5mm might work too. Nylon bolts are good too I used them on my previous frame.

The paint seems decent but I think it's not done well around the bolts. They leave the bolts and the washers on and when you remove them there's a large round area without paint. Also taking out the washers ripped some more paint off beside them. I need to get some touch up paint because the plugs won't cover them fully.


https://www.aliexpress.com/item/1005010042834440.html
https://www.aliexpress.com/item/1005005545776418.html