Here you go.  Fantastic price if you are into the SRAM XD.

https://planetcyclery.com/dt-swiss-xm1700-spline-29-wheelset

Screaming deal. Thanks,  just ordered.

Picked up e13 TRS Race carbon cranks in Super Boost for $176.

I think I have everything else.

Someone should put together a group buy.

I bought a pair of Carbon Beam 29" 30x30 rims for my ICAN build, put them on Venfort DT copies for a total built weight of 1425g. I chose the lightweight 315g for front and AM 360g for the rear. They are cheap at $130usd each including delivery.

However in less than 100km the rear is destroyed by a rock strike. Now I get that rock strikes aren't warranty, however when it comes down to it, the seller advertises these as AM with a weight rating of 120kg for mountain bike use. I didn't even hear the rock strike and have been pretty careful on this bike to ensure my riding isn't as enthusiastic so to speak as my heavier duty enduro bike. That said, I have destroyed several aluminium rims over the last couple of years, but they are a LOT cheaper too...

I had a look at Lightbicycle, they have a great writeup on different layups and light/standard/heavy duty layup options, however their rims come out to $366 ea delivered.

Is a $366 rim less prone to destruction from rock strike than a $130 rim?

To answer your question, yes, the LB or any of the other 4 or 5 brands you see lots of good recommendations for on Chinertown would be better (I'm partial to Btlos but wouldn't hesitate to buy the others).  I'd expect higher quality and also better service.  I had a friend crack a rim in a similar situation, first week or so of riding and no mark on the rim.  After a few questions and some photos, he was sent a new rim.  No need to name the company, they've got lots of positive reviews and I wouldn't hesitate to order from them if I needed a new wheel set.

Does the rim show any strike marks?  Did you reach out to Carbon Beam? 

Make sure the fit system is 360 degrees. I bought a Chiner helmet and the head band that you adjust by turning the nob was not 360 degrees.  It only went a little over half way around the back of my head.  Doesn't fit as good or feel as comfortable.

Hello from Russia!
I buy such frame in L size and white color from another aliexpress seller.
Briefly:
This is high modulus carbon frame like original SJ MY19.
But... i kill tread on one rear bolt (M12 body and M11x1 tread) - make new from В95Т1 alloy on home lathe.
Top eye shock M6x1 bolt was 90 degree champfer, but frame (as original) have 120 degree champfer... make new from В95Т1 alloy on home lathe.
There is no holes for place hosings in middle tube (as in original manual), but SWAT hile is absent and all housing plased in bottom tube.
I buy dropper OneUp v2 180mm. Frame have slight problem to place dropper more than 17cm, but i cut 1mm from diameter of dropper ass and get 22 cm!
Original bolts have rubber seal, i simple print TPU seal on printer.
Complect seat post clamp have ~40.5mm diameter instead 38.6mm, buy right item on aliexpress.
Original flipchip have big size and you need mill additional space in yoke if you whant it. As i understand that tight flipchip block bottom eye frop any rotation. But default china yoke set in "XC" position - not bad choice.

Geometry precisely mathed to info by aliexpress lots! But have no such geometries in linkage web base. See attached *.itx file for linkageX3 software.
For this frame maximum drive chain about 32T, but pedal efficiency at this 90..80%, if you move gravity mass to front - efficiency increase. I think that 28T (or may be 26T oval) and 9..42T cog wery good variant - for 28T drive antisquat about 100..110%.

Positives:
$800
Nice look.
Light weight (may be it good moment).
Compatible with  "old" common 210x55 shox - simple to find in sale section.

Negatives:
No SWAT! $(
No frame guards (use 3d printer...)
Decals above paint lyers. I use oraguard anti stone TPU film.
Frame have very thin wall in BB link region - may be this is normal, but...

Good job making everything work correctly.

New owner here, love the frame, I'll post some thoughts after a couple more rides, just got a few initial questions I couldn't find answers to on here:
1) what are people doing to plug up the cable holes on top of the chain stays? Or is it easy to just wash out when mud gets down in there?
2) supplied hanger doesn't seem to work with my slx 12 speed, only way I can access the smallest cog is to add a fat washer to locate the derailleur further outboard. Yes I checked hanger is straight, and limit screw all the way out. Anyone else find this?

No problems with my XTR derailleur. I think I have an extra hanger if you want to try it.

I just recieved my frame from groupbuy B. Size L. :-)

I knew we could count on Stefan to add one of these to his collection. Anxious to see how you build it out.

Got my moss green medium today. I'll post some pics and weight tomorrow. Ordered a DT Swiss F535 160 to go up front. Missing a few small things, but will get started on the build.