Likes given

Profile Info

See likes

See likes given/taken

Posts you liked

Pages: [1]

Post info	No. of Likes
Re: Velobuild AERO GRAV Frame Quote from: Valdes on October 27, 2025, 01:57:30 PM Hi, This is my third Velobuild and I am having some issues with the handlebar for the first time. I can't remove some side to side play. It only happens to the right side and only when I stand up on the pedals pushing hard. Stem bolts tighten to 7nm and cap bolt by feel. Are the top and bottom headset bearings identical and interchangeable? Or each one must be in its right place? The hidraulic brakes cables are a little bit too tense pushing the C shape spacer to the right side. Could it be the reason? THanks! bearings are the same top and bottom. I dont think the cables could do it. Double check if headset is well compressed, especially if bearings are well on their place. October 28, 2025, 03:24:05 AM	1
Re: VeloBuild VB-TT-023 And here are some files. I got the bridge and the angle piece made from 6061-T6 aluminum with a black hard-anodized finish. The bridge has a variety of mounting holes, on a slightly different pattern than the original bridge. I also pre-angled the mounting pattern inwards by 1 degree to get my hands a little closer together. The angle piece requires flat-head M5 bolts which attach the angle piece to the bridge before being attached to the base bars. Flat 90 degree SRAM wireless blip mounts: https://www.printables.com/model/1475910-wireless-blip-holder-for-time-trial-and-triathlon Tool box for Large frame: https://www.printables.com/model/1475920-frame-tool-box-for-velobuild-tt-023-triathlon-bike Closed back elbow pad extensions: https://www.printables.com/model/1475931-closed-back-elbow-pad-extensions-for-velobuild-tt November 09, 2025, 11:15:10 PM	1

Post info

No. of Likes

Re: Velobuild AERO GRAV Frame

Quote from: Valdes on October 27, 2025, 01:57:30 PM

Hi, This is my third Velobuild and I am having some issues with the handlebar for the first time. I can't remove some side to side play. It only happens to the right side and only when I stand up on the pedals pushing hard. Stem bolts tighten to 7nm and cap bolt by feel.

Are the top and bottom headset bearings identical and interchangeable? Or each one must be in its right place?
The hidraulic brakes cables are a little bit too tense pushing the C shape spacer to the right side. Could it be the reason?

THanks!

bearings are the same top and bottom. I dont think the cables could do it. Double check if headset is well compressed, especially if bearings are well on their place.
October 28, 2025, 03:24:05 AM

Re: VeloBuild VB-TT-023 And here are some files. I got the bridge and the angle piece made from 6061-T6 aluminum with a black hard-anodized finish.

The bridge has a variety of mounting holes, on a slightly different pattern than the original bridge. I also pre-angled the mounting pattern inwards by 1 degree to get my hands a little closer together.
The angle piece requires flat-head M5 bolts which attach the angle piece to the bridge before being attached to the base bars.

Flat 90 degree SRAM wireless blip mounts: https://www.printables.com/model/1475910-wireless-blip-holder-for-time-trial-and-triathlon
Tool box for Large frame: https://www.printables.com/model/1475920-frame-tool-box-for-velobuild-tt-023-triathlon-bike
Closed back elbow pad extensions: https://www.printables.com/model/1475931-closed-back-elbow-pad-extensions-for-velobuild-tt
November 09, 2025, 11:15:10 PM

News:

See likes

Posts you liked