Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - raygutt

#2
Back after a three month hiatus...

My LBS had some issues with the front calliper and asked Chris for a new fork. It took some time but finally I got my bike ready to go.

I rode cautiously from the LBS and put it on my hometrainer to fine tune the position and check if everything is OK.

On this picture, I have a total of 35mm spacers (which I guess is the default with the provided screw), I felt OK but maybe a bit too low to get started with a TT position so I added a few spacers for a total of 80mm. FWIW, i could spend 1h15 in the aero position watching Milano/San Remo on the turbo, so I guess it means I'm comfortable with this fit.

Waiting for a not too windy day to try it outdoor. Can't wait.
#3
I have a total amount of 2x200m spacers made of 5mm, 10mm, 20mm spacers. I can use as much as I want as long as I find the right screw. (I will order a few threaded rods and cut them to the right length.

by the way, I thought it was M4 screws, are you sure I need M5 screws ?
#4
If you don't mind, boulette, I will post my (ongoing) build in your thread... and make it the "French VB TT-023" thread  :D

I received my frameset last friday (about one month after ordering it). I allready had all the components ready. It will be a 1x wireless Rival AXS 12s build (no blip box)

Crankset Magene   PES 515 (powermeter) 165mm
with Pass Quest   SHIMANO X110BCD (4-bolt AERO) Narrow Wide 50t chainring
and Nova Ride   BB T47 85.5 for Shimano    BB

rear derailleur: SRAM   Rival eTap AXS 12s
1 pair of SRAM wireless blips with Leap Components Adapters
1 pair of SRAM wireless blips (for the basebar)
SRAM   XG-1250 cassette
Rival 12s flattop chain (waxed)

Brakes:   SRAM   S900
Pedals: Shimano   Dura-Ace PD-R9100 (second-hand)

Wheels: Yoleo 88m   
Tires: Continental   Grand Prix 5000 All Season 28mm
Tubes: Vittoria   Competition Latex
      
Saddle ISM   PN 1.1 (second hand)



I'll have the fork cut and the brakes installed by a LBS, but I'll have to wait until the end of the week for the mechanic to be available.

Can't wait, so I build a few components to see how it goes...

I asked Chris to add a few handlebar spacers. He gave me 2x20 cm...

#5
Quote from: boulette on October 14, 2025, 11:31:42 AM
You Will need some extra spacers, no doubt about it.
I live in val d'Oise, what about you ? Could be funny to meet up once our Bikes are ready 😁

Opposite side...  Val-de-Marne ;D  I'm very close to the "Polygone de Vincennes", if you know this place. That's where I plan to get used to riding this bike, after bike fitting on my trainer.

Hopefully someday we can meet, ride together & have pictures of our bikes together.  8)

Initially, I picked the same raw/no painting frameset as you, and then I came across this color, which happens to be very close to my triathlon club's colors...
#6
Hi, Samir

I'm also living near Paris, and ordered a frameset that should arrive early november...

I read your thread with great interest, and asked Chris to add some spacers, just in case... i'm 181cm/89 inseam and chose a M-sized frame, so it might be useful...