Show Posts
1
Component Deals & Selection / Re: Avid BB7s... What's the real deal on these?
« on: October 11, 2016, 08:11:54 AM »
Registered just to weigh in on this. I run Avid BB7's from 2008 on my Redline Monocog.
InstallationLow friction cable/housing is important. Make sure you use bypass cutters to snip everything to length and grind the cut flat. Use a small nail to open the cable end back up, often times the anti friction material can close over the hole when you cut the housing. All these steps are important to get the best response at the lever.
Rotor Set UpWhen setting up the caliper, tighten the caliper mounting bolts to your adapters to the point that the caliper can be easily shifted side to side but not up and down. Back both dials on the caliper all the way out. Now tighten each dial 10 turns, then tighten each one 4 more turns, then tighten each 2 more turns. What you are trying to do is get equal engagement of the caliper on the rotor. Do this until the wheel will not rotate. Now tighten down your caliper mounting bolts to spec. Back the pad adjustment dials off by an equal number of clicks until you get the feel you want with no rotor rub. Because my bike uses sliding dropouts I have to do this procedure anytime I change out my wheels, cogs, or adjust the dropouts to tow my kids trailer. This procedure always works for me and I can do it in 4 minutes or less. Make sure to adjust your levers to adjust your engagement point.
Performance I'm 6'1 and around 225lbs so technically a clyde. I run 180mm rotors as a result. The BB7 brakes work well for midwest riding and around town dirt road action but they don't do much for me in real all mountain situations. They fade easily and fatigue my forearms on extended downhills. A few years back in Arizona they faded to the point that I almost lost control and about launched off a 50 foot cliff. I bought some brand new Shimano XT brakes with Ice Tech rotors the next day. Those brakes stay on my All Mountain bike where they belong and I love them. The BB7 brakes are good in most situations but not all, at least for me.
When I bought the Redline Monocog it came with a set of Avid BB5 brakes and levers, I immediately swapped in the BB7 and levers I already had. The difference is that a BB5 can only adjust the outboard pad while the BB7 can adjust inboard and outboard. I still have the BB5 brakes and levers, might even have the 160mm rotors. Let me know if you'd like them, I will sell them to you real cheap just to clear out space in the parts bin.
Hope this info helps. I'm new to the Chinertown boards and look forward to learning more. Hoping to build up a HT 29+ bike sometime before next spring.
InstallationLow friction cable/housing is important. Make sure you use bypass cutters to snip everything to length and grind the cut flat. Use a small nail to open the cable end back up, often times the anti friction material can close over the hole when you cut the housing. All these steps are important to get the best response at the lever.
Rotor Set UpWhen setting up the caliper, tighten the caliper mounting bolts to your adapters to the point that the caliper can be easily shifted side to side but not up and down. Back both dials on the caliper all the way out. Now tighten each dial 10 turns, then tighten each one 4 more turns, then tighten each 2 more turns. What you are trying to do is get equal engagement of the caliper on the rotor. Do this until the wheel will not rotate. Now tighten down your caliper mounting bolts to spec. Back the pad adjustment dials off by an equal number of clicks until you get the feel you want with no rotor rub. Because my bike uses sliding dropouts I have to do this procedure anytime I change out my wheels, cogs, or adjust the dropouts to tow my kids trailer. This procedure always works for me and I can do it in 4 minutes or less. Make sure to adjust your levers to adjust your engagement point.
Performance I'm 6'1 and around 225lbs so technically a clyde. I run 180mm rotors as a result. The BB7 brakes work well for midwest riding and around town dirt road action but they don't do much for me in real all mountain situations. They fade easily and fatigue my forearms on extended downhills. A few years back in Arizona they faded to the point that I almost lost control and about launched off a 50 foot cliff. I bought some brand new Shimano XT brakes with Ice Tech rotors the next day. Those brakes stay on my All Mountain bike where they belong and I love them. The BB7 brakes are good in most situations but not all, at least for me.
When I bought the Redline Monocog it came with a set of Avid BB5 brakes and levers, I immediately swapped in the BB7 and levers I already had. The difference is that a BB5 can only adjust the outboard pad while the BB7 can adjust inboard and outboard. I still have the BB5 brakes and levers, might even have the 160mm rotors. Let me know if you'd like them, I will sell them to you real cheap just to clear out space in the parts bin.
Hope this info helps. I'm new to the Chinertown boards and look forward to learning more. Hoping to build up a HT 29+ bike sometime before next spring.