Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - valvze

#1
Quote from: brandon08 on September 30, 2026, 08:06:41 PM
Just joined the forum. What a great resource - thanks everyone for all the helpful information.

I'm trying to make sense of LightCarbon's sizing recommendation for the LCR018-D. They recommend a 52cm for riders 173-179cm. That frame has an effective top tube of 535mm and a standover of 75.6cm.

For comparison, a 51cm Cannondale Synapse is recommended for riders 165-175cm It has an effective top tube of 542mm and standover of 75.2cm - not very far off from the LCR018.

A medium Trek Domane Gen 5 is recommended for riders 162-173cm. It's effective top tube is 541mm and much higher standover of 775mm.

I'm 171cm with a 76.8cm inseam. The Synapse in 51cm and the Domane in medium both fit me. The LCR018 52cm doesn't seem any bigger than these endurance frames, and might even be a little smaller. And yet it's recommended for riders 173cm. I'd also be running 700x32 tires, which might drop the standover a bit more. But LightBicycle recommends the 50cm for me, and from what I'm reading here, that would probably be what most people would recommend for me as well. But it really seems like a 52cm LCR018 is the closer match to these other frames that I know are my size. I need the higher stack of the 52cm. I'm moving from a silly-looking 52cm Aethos with a massive spacer tower and 17 degree stem. I'd still probably need 20-30mm of spacers on the LCR018. The 50cm would probably fit too, but everything points to the 52cm for a 171cm rider.

Am I missing something?

Just to add another data point if it helps, I am 173 cm with 80 cm inseam on the dot and went with a size 50 instead of the 52. I think it's better to err on the side of caution since it's a lot easier to make the smaller bike bigger than vice versa.

Glad I went with size 50. I do have have to run 2 cm of spacers with the 110 mm stem but it fits really well, and I no longer get any neck pain compared to my supersix evo which was 20 mm lower and 20 mm longer than this bike.

#2
Quote from: jksu on September 28, 2026, 11:01:04 AM
for those of us who waited close to 3mo, the 2 week turnaround for your bike is awesome.  and agree, best parts (both fun and cost-wise) of building up a LC bike, is specing the parts/crank lengths/stem-bar etc combos and not needing the extra costs of buying replacement parts when you get an off the rack bike from one of the major brands.

had similar feelings coming from a rim brake parlee altum w/dura ace 11speed, but am getting used to di2 (and enjoying not worrying about stretched/frayed shift cables anymore).  definitely enjoying the endurance geometry and stability in fast descents.

i've dialed out my front end harshness with slightly less (2psi) front tire pressure vs the rear and it's taken the sting out while still feeling fast and safe from pinch flats (tpu tubes).

consider a small battery operated pump - the little ones can fit in the downtube storage area.

i'm loving the bike enough to definitely consider another frame from LC.  when they come out with a gravel model that can accommodate 2.2 tires, i'll definitely consider it.

Yeah I think I may have just gotten lucky and everything except the fork was in stock. I originally asked for a gloss finish and also a 120/38 bar but  was told it'd take close to a month to get this spec. I'm very impatient so I just ordered what they had and luckily the 110 feels pretty good, 120 may have been too long. I don't mind the basic matte finish either because a lot of budget carbon rims are matte as well and it doesn't look too bad all matched up.

After a fast bunch ride this morning and pulling some turns at 45 kph, definitely notice the compounded benefit of the aero tubing, wider tyres, and waxed drivetrain compared to my supersix. It's a lot easier to maintain a steady power output going from 172.5 to 165, honestly regret not going even shorter. One bloke with a Pinarello was poking fun of my 'temu' bike at the start but didn't hear a word from him after towing the bunch around ;D

Di2 is pretty good, but the engineering sophistication of high end mechanical groupsets like Red and Dura-Ace is like art to me compared to a servo. Although on this frame as a first time builder, I reckon mechanical routing would have been an awful nightmare, electric is very nice for that reason.

The pressure's a good call - I think I will end up selling the Superteams though as they're not doing the frame any justice. Am considering some wider and deeper (60mm) XMCS or similar so I can run 32/34s without mushrooming. I like that rims are no longer a consumable coming from a rim brake bike so it's easier for me to justify spending a little extra knowing I'm not burning through cash as I brake on a descent haha.

Yeah it's definitely unfortunate about my pump. Will get a new one after this one craps out inevitably or may just switch to the goofy narrow pocket handpump. I was kind of disappointed to find out a lot of these e-pumps have limited longevity. Do you have any recommendations for one that fits?
#3
Wanted to share my build of the Lightcarbon LCR18, first post on Chinertown so hi everyone!!

For context: I came off a rim brake 2019 Supersix Evo. This build cost $3300 AUD, weighs just over 8kg with Ultegra Di2 and budget carbon wheels. I'm a weekend rider, ~4hrs/week, 3w/kg threshold, 900w sprint, just basically an average punter :'(

Ordering: Placed order with Carol at LC on Sept 7th, frame arrived Sept 23rd. Size 50, UD matte black, 110/38 bar. Skipped custom paint to avoid getting sad over inevitable paint chips ($1120 AUD)

Quality: No voids I could see (no endoscope though), brake mounts/BB faced properly, headset seats held on to bearings firmly, supplied BB threaded in by hand with no issue. Downtube storage doesn't rattle even without any brake liner. Handlebars are step up from my old Kocevlo ones definitely.

The build itself:

Cutting the fork was the scariest part, but luckily got it first try with a hacksaw, 32 TPI blade, and a guide.
Hose routing through the bar was fiddly, broke a tool but got there with some needle nose pliers.
Didn't torque the BB properly
Magene P515 crankset (280 AUD from Taobao) needed some spacers to remove play, no creaking 100km in. Paired fine with phone/computer via the Chinese Magene app.
Ultegra Di2 (1200 AUD off Taobao) is nice but not life-changing coming from Dura Ace 9100 rim brake. Honestly think I prefer the tactile feedback on mechanical and slamming up and down the cassette but I appreciate that this needs less maintenance (fingers crossed!)

Brake bleeding was a pain, my funnel cup kept leaked, contaminated a pad/rotor, but I've got new ones on the way.
Superteam Classic wheels are fine and do the job. I wanted Tagoola Cure but they were out of stock at the time.

On the road: Very stable thanks to longer wheelbase/trail, definitely not as twitchy as the Supersix, but this is reasonable for an endurance frame. Can't really judge speed difference yet, but the aero tuck with 90 degree elbows is easier with the higher stack/shorter cranks. Chipseal transmits more vibration up front than the supersix I think because of the bigger tubing so fat tyres are a must. I bought 30c but regret not going 32 or 34. The bar's 8mm rise pushes your shoulders inward when resting hands on the flats because of the curve. Not a huge issue but not the biggest fan of this design choice. At least it looks pretty cool. Rear end is noticeably more compliant than the front (maybe from dropped seat stays?)

Annoyances: Downtube storage doesn't fit my pump so I still need a saddle bag, thru axles need allen key (does anyone know if I can get thru axles with a handle anywhere that fit?), seatpost bolts hard to torque. Seatpost slippage was a non-issue with some carbon paste though.

Overall: Way smoother build than expected. Get a bike stand if you're doing this solo but I had help balancing the frame around and still recommend one. Value is insane, cheapest comparable brand new bike here in Aus (Polygon Strattos with Ultegra) is $700 more and comes with no power meter, wrong saddle, one-piece bar/stem, and wrong crank length. Carol from LC was responsive daily. No obvious frame defects to the naked eye, very happy with it, would buy from them again - maybe the LCR20!!