Quote from: eucalyptus on June 24, 2026, 01:48:37 AM
Aliexpress in a nutshell haha
Needed bearings for a pair of Xpedo CX pro pedals, same used in Favero I think. Very niche sizing

Made in Germany is the marketing thing
Made in China on the backside 

I figured how much worse could they be than stock bearings, look identical almost.

These are decent bearings. I used them in my hubs

Solved my issue today running the Xcadey Gen 1 spider (3 bolt 110BCD for road). Works with 73mm BB shell if you run it with a MTB crank (longer spindle) that is also 3 bolt. Bike is BSA bottom bracket, so I had to run 2.5mm spacer on the drive side. Added an addition 0.5 shim onto the bottom bracket to give it a little better chain line.

Quote from: gribs on June 29, 2026, 06:45:33 AM
I'm using a Xcadey Xpower-s gen two on Shimano SLX cranks and I'm not sure if I can recommend it. The first unit died within a couple of weeks. The replacement seems ok after a couple of months (but it's been dry)and the readings are consistent, if about 10% higher than my Magene pedals or Kickr smart trainer.

Yes I have heard some mix quality on gen 2...I have gen 1 but I guess for road.

I don't think Magene has SPD (MTB) power pedals?

Wondering if someone has a recommendation for power meter for MTB or should I say for 73mm width BB shell. I don't think I see too many options out there.

I do have a XCadey spider that is 3 bolt with Zrace RX crank set but seems like the crank spindle is not long enough. If someone has a recommendation for crank then I can reuse the spider. It seems like the spider has quite a bit of offset.

I have recently picked up a Giant and it uses the OD2 standard. Was wondering if there are current recommendations for OD2 that is stiff and relatively easy to route for internal brake hose (Di2 setup)?

Quote from: serenadebikes on April 29, 2026, 07:51:12 AM
No ratchet tool required.

The 15267 bearing is smaller than the ratchet ring.

according to the site it uses 2802 but you mentioned 15267. Which one is correct and both still smaller than the ratchet ring?

https://serenadebikes.com/product/serenade-sr278c-rear-and-front-20-holes-road-bicycle-disc-brake-hub-for-carbon-fiber-spokes/

I use the calibrate on my Garmin (530) it seems to work. Bike stationary and upright. I have the crank at 6 and 12 o'clock.

Anyone tried the backpedal 5 times ?

too early to service but thinking down the road, what tools is needed for the SR278C hubs? I think it needs a special tool like DT swiss to remove the ratchet ring in order to remove the bearings?

Finally the weather is good enough for my first test run after purchasing a set from Black Friday discount. I got something I guess a little usual compare to everyone else, 21mm internal with asymmetrical rim, 50mm deep and carbon spokes. Works out to be 1180g. First test ride of 40km, wheel/bike feels fast and stiff (may need to adjust tire pressure a little). But the acceleration and snappiness is like instant!  Looking for more long term testing.

Quote from: edy on April 20, 2026, 03:35:30 AM
Just watched/listened to your posts on these wheels yesterday. Cool stuff!

The thing is, I mostly do longer and steeper climbs when and where possible. I currently run ICAN AERO35s with 21 mm internal and 35 mm depth on Sapim cx-ray spokes that weight just below 1300 g that I bought new on auction for a fraction of the sticker price. The wheels are fine and all, but I am very tempted to try deeper wheels with carbon spokes (3.5 or even 5 mm) and would love to decrease the weight if possible. I will also need to check the aesthetics of 60 mm deep wheels on my bike.

You can definitely go lighter and deeper. I got 21mm internal with 50mm deep and 3.5mm carbon spoke. Weight 1180g for the pair.

Anyone know of the zrace rx crank with dub spindle if the spindle is long enough for MTB bb shell? I think it is but haven't tried it.

I ended up getting the Tabolu mtb shoes. They work ok but the insole that it came with is too soft. I would recommend switching out the insole for something stiffer. Felt much better after swapping it out. Walking wise they were comfortable. This was my first mtb shoe so the outer sole is definitely more flexible compare to my carbon road shoes so I don't have a reference if the sole is too flexible or not.

Quote from: Icyseanfitz on February 04, 2026, 05:25:49 AM
Eagerly awaiting mine, are they easy to setup? Has geoid their own app or is it magene

it definitely pairs with the Magene app. Haven't seen any firmware update so not sure if that is how we will receive it

Anyone spent some time with this PM? Winter over here so I couldn't really test it out

It is an Easton interface. So you can find other cranks