Velobuild VB-R-218

[JonMS]

Mine is showing up in the next couple of hours.

Are you airbrushing on the decals yourself or having it done outside ?
I have a couple of designs in my head that I want to get done & put on the frame & clearcoated

Did your frame show yet? Having trouble getting my bottom bracket threaded in both sides.

[madmax]

Did your frame show yet? Having trouble getting my bottom bracket threaded in both sides.

Should be here by 4:30 PM PST per Fedex
Mine is the rim brake version with BSA threads, so remember crank side is left threaded, ie lefty-tighty  (double check this)

1. Check threads for any paints & clean the inside very carefully with a shop towel & isopropyl alcohol to get any gunk out of the threads

2. DO NOT force the threads. if doubt take it to local shop where they can get the bracket in for you or rethread if needed.

3. Ideally, you should be able to use a light smear of grease, polylube1000 or asc-1 (anti-seize) & be able to screw the bottoms in & finger tighten them without cross-threading

[madmax]

Box showed up..... somewhat opened/dented

Parts all over the bottom of the box. I will post a pix on these, as I am not sure if I'm actually missing parts/screws/caps now or if everything is included
Frame is wrapped & not opened yet & will examine this after work & take a pix

If someone can post a pix of their parts after opening the box, it would be appreciated....

[JonMS]

Should be here by 4:30 PM PST per Fedex
Mine is the rim brake version with BSA threads, so remember crank side is left threaded, ie lefty-tighty  (double check this)

1. Check threads for any paints & clean the inside very carefully with a shop towel & isopropyl alcohol to get any gunk out of the threads

2. DO NOT force the threads. if doubt take it to local shop where they can get the bracket in for you or rethread if needed.

3. Ideally, you should be able to use a light smear of grease, polylube1000 or asc-1 (anti-seize) & be able to screw the bottoms in & finger tighten them without cross-threading

Thanks, I got it. Paint in the threads was worse than it looked. Used a wire brush and an older BSA BB I had lying around to test/chase the threads with until it was butter. I had file down the center rivet almost flat to get my DUB BB to fit. Thankfully the provided bolt is already short enough so that didn't need any modification.

[madmax]

Here's the pix of all the parts that fell into & out of the box as soon as it was opened

I think I am missing the Garmin mount that I paid for & probably the top cap cover

[madmax]

Thanks, I got it. Paint in the threads was worse than it looked. Used a wire brush and an older BSA BB I had lying around to test/chase the threads with until it was butter. I had file down the center rivet almost flat to get my DUB BB to fit. Thankfully the provided bolt is already short enough so that didn't need any modification.

Just checked my box & frame & there almost no paint in the threads in the BB.

I am missing  stem cover with "P" logo or whatever,  Garmin mount & optional skewers for the rims (I don't know if they actually send those with the frame or not)

I have 2 alum pieces & 3 metals pieces (which go on teh frame), or I have no ideas where those are used

[JonMS]

Just checked my box & frame & there almost no paint in the threads in the BB.

I am missing  stem cover with "P" logo or whatever,  Garmin mount & optional skewers for the rims (I don't know if they actually send those with the frame or not)

I have 2 alum pieces & 3 metals pieces (which go on teh frame), or I have no ideas where those are used

You’re missing a couple headset spacer items. I got a Garmin mount that came with my frame. You seem to have an extra set of grub screws for yours. Lol what a mess. Are you US based? I actually bought spare headset spacers and might be able to help you out if velobuild is painful on getting you your parts.

[madmax]

You’re missing a couple headset spacer items. I got a Garmin mount that came with my frame. You seem to have an extra set of grub screws for yours. Lol what a mess. Are you US based? I actually bought spare headset spacers and might be able to help you out if velobuild is painful on getting you your parts.

Just sent you a PM. I have emailed Chris on the missing parts, but I am confused on what parts should actually be there

[Sebastian]

Here's the pix of all the parts that fell into & out of the box as soon as it was opened

I think I am missing the Garmin mount that I paid for & probably the top cap cover

You are missing the top cap and most importantly you are missing the upper headset bearing cap that the two piece spacers sit on top of.
The black metal parts are the wedges for the seatpost and handlebar. For those you’ll need the grub screws. The two piece silver aluminium part is a Di2 battery adapter. You can ignore that if you’re using a mechanical groupset. There’s also a battery holder inside attached to the bottom bracket cover that you won’t need.

[madmax]

Here's a cleaner pix taken 5 min ago & added numbers & folks can correct me if I am wrong

1. Headset compression plug
2. Bearing #1
3. Bearing #1 bottom race
4. Bearing #2
5. Bearing #2 top race
6. Various screws for seat-post etc
7. Spacer (big)
8. Spacer (small)
9. Bottom or top ?
10. Wedge for ?
11. Wedge for ?
12. Wedge for ?
13. Di2 battery adapter


I think I am missing only the top cap & the garmin mount at this point.

Does anything look broken or missing to you guys ?

[coffeebreak]

#9 looks like dust cap. All your headset spacers will go on top of it

[JonMS]

Here's a cleaner pix taken 5 min ago & added numbers & folks can correct me if I am wrong

1. Headset compression plug
2. Bearing #1
3. Bearing #1 bottom race
4. Bearing #2
5. Bearing #2 top race
6. Various screws for seat-post etc
7. Spacer (big)
8. Spacer (small)
9. Bottom (goes ontop of 5 and is keyed)
10. Wedge for seat post
11. Wedge for stem
12. Wedge for seat post
13. Di2 battery adapter


I think I am missing only the top cap & the garmin mount at this point.

Does anything look broken or missing to you guys ?

[Queen of Skulls]

Ok I finished my paint scheme.... what does every one think? the inside of the stays and fork will be pink too. I need to make the mask for the purple paint transition. But getting chris to tell me the file type needed is like pulling teeth. I hope they can do it. otherwise I will have to and it will be a pain.

I need to get some stickers made to say Skull-ma... and Bonerello... haha

[madmax]

Paint scheme looks awesome

“Donatello” for a more Italian name + skull with turtle shell and bandanna should look …..

[Queen of Skulls]

Paint scheme looks awesome



“Donatello” for a more Italian name + skull with turtle shell and bandanna should look …..

How about we say we did but don't actually... I am the queen of skulls and I have to ride a skull pun bike