Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Igital96

Pages: [1] 2 3 4
1
Apparently this is the new geometry.  :D

The reach now is very similar to the FM336 so I think this is an upgrade definitely.

2
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 18, 2026, 05:58:15 AM »
Just to clarify that 0. is the lexon spacer which match either 1. or 2.

3 and 4.compresion ring and seal that comes with frameset.

Combination of 0 + 1 means spacer is touching the top tube (to less gap) or 0 + 2 will result in a too big gap between spacers and frame.
Combination of 0 + 3 + 4 also leads to a big gap.

Obviously the headset kit from frameset (not reflected in the picture) I do not consider since this is not compatible with handlebar from Lexon.

Any help?

The correct order would be: #1 on top of the bearing (inner race of the bearing), then insert the fork to make it tight and then #4. After that then #0. If you dont use #4 the base of the handlebar will rub against the frame. The compression ring #1 is very important so the fork is secured and tight. Otherwise there is going to be a lot movement (I did and undid the headset like 5 times  ;D)

3
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 16, 2026, 10:28:09 AM »
I really love this color, is it going from purple to gold? Doesn’t look like it on the photo.

Yes. When the sun hits in a certain angle it looks like gold

4
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 16, 2026, 09:24:47 AM »
I am glad I inspired some people  ;D

5
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 09, 2026, 07:36:10 AM »
you're an influencer now, i received my serenade wheels today after your initial post.

I hope you are satisfied with them! It's always a bit of gamble. At the end of the day, it's my personal experience! I am glad I am "influencing" people" in that way.


6
Absolute banger of a frame. If it's manufactured and rides as good as it looks, chapeu. Enjoy building it!

8
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 08, 2026, 07:10:07 AM »
Paisano! Te sigo 💪🏻

Gracias! I didn't want to advertise my profile but just so people know it's my bike and not someone elses stealing my pics haha

9
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 08, 2026, 04:03:50 AM »
I want to be famous like you 🤣🤣🤣🤣🤣

THAT'S NOT ME! MY instagram page is @Dirtdynamo. Apparently he is a designer that works at Serenade haha. Crazy how quick my pictures fly around. Call me trendsetter  8)

10
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: June 01, 2026, 04:33:19 AM »
I ordered same frame colour and last week same wheels, but 40mm 🤣

Twin  ;D

11
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: May 30, 2026, 04:22:19 PM »
Do you have them? If so, how long did it take to arrive? or maybe someone else can give more insights about shipping time

I have them. I am the owner of the purple FM336 that you can find in previous pages of this thread and in reddit. I have done 600km with those wheels (G-One RS + Vittoria Airliners) They are indestructible so far. I have had a fall where I ate a tree that was laying on the ground and I didn't see, and the wheel ate like nothing. Spokes kept the tension and the rim has no damage. I have eaten potholes because I didn't see them while chatting with my ride-pal and nothing. They weight 1390+- GR, 30mm IW, 36mm EW, 50 mm deep.

It took one week and a half for delivery (Germany). Production time, I don't know. Maybe the setup you want is already in stock. You must contact them through WhatsApp to know further information.

12
Cyclocross Frames, Wheels & Components / Re: Best gravel handlebars
« on: May 27, 2026, 08:50:38 AM »
I am using the Lexon Unox Gravel handlebar and no problems so far. I love the flare and they have not done any cracking sounds so far. I will keep you updated.

13
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: May 27, 2026, 01:07:07 AM »
It is tight but fits, I think I should be able to fit a 50mm on my side as well. You mentioned there is clearance for 5mm on each side, its seems to bit a bit less, maybe the perspective of the picture fake it a bit?. Did you mentioned once you have measured it at around 52mm total width? That would give a total physical clearance of 62mm, which I believe is a lot and not representing the reality.

I trust on you anyway but I will double check with my frame before ordering the tyres. Thanks a lot

I will double check again but yes, the inflate to approx 52mm. I haven't had any rubbing or anything at the fork. 45mm tires will inflate to 48-49 so I think that's safer if you want to do that. Also my tire doesn't have tall knobs. If you are going with the PRO R or RX that could be tighter.

14
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: May 26, 2026, 01:28:32 PM »
Maybe I oversaw it. Sorry
That is exactly my plan 45 rear with G-One R PRO 700 x 45 and G-One R PRO 700 x 50 front and wheels Depth 45mm x inner width 30mm x outer width 36mm.
Could you tell me how much clearance do you have at front?

15
Cyclocross Frames, Wheels & Components / Re: Mondince FM336
« on: May 25, 2026, 07:21:57 AM »
I finally have two options for the tyres:

Option 1:
Tyres Front: Schwalbe G-One R PRO 700 x 50mm
Tyres Rear: Schwalbe G-One R PRO 700 x 45mm
Wheelset geometry: Depth 45mm x inner width 24mm x outer width 31mm

Option 2:
Tyres Front: Schwalbe G-One R PRO 700 x 45mm
Tyres Rear: Schwalbe G-One R PRO 700 x 45mm
Wheelset geometry: Depth 45mm x inner width 30mm x outer width 36mm

Of course option 1 is risky, since it theoretically let me keep only 4,4mm clearance on each side at fork.
What do you guys think?

Hello, I don't know if you saw my post but I am using wheels with the same measurements as yours and I am running G-ONE RS 50mm front and G-ONE RS 45mm rear with vittoria airliners inside and no problem. There is enough clearance (6mm each side rear and maybe 5mm at the front)

Pages: [1] 2 3 4