Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Machine

Pages: [1]
1
Road Bike Frames, Wheels & Components / Re: Winter bike frame: 32mm with fenders & no toe overlap?
« on: November 21, 2024, 10:40:18 PM »
Hahaha on Tideace! I’ve seen some pretty bad English translations, but straight AI-generated with no proof reading has to take the cake!

2
Road Bike Frames, Wheels & Components / Re: Winter bike frame: 32mm with fenders & no toe overlap?
« on: November 21, 2024, 10:26:00 PM »
Thank you! I’ll take a look at that one, it was not on my radar.

3
Road Bike Frames, Wheels & Components / Winter bike frame: 32mm with fenders & no toe overlap?
« on: November 21, 2024, 12:29:50 PM »
Looking to build a dedicated performance winter road bike. Needs to accept fenders and clear a 32mm tire with fenders, preferably with no toe overlap on my 170mm cranks. Hoping for classic road/endurance handling, so some of these newer gravel bikes with slack head tubes don’t fit the bill. Any suggestions!! Thank you

4
Road Bike Frames, Wheels & Components / Re: Boost Road/Gravel Bikepacking Frames.
« on: June 28, 2024, 05:55:20 PM »
I too have been looking for this. Haven’t found anything yet. I’m surprised no one has copied the cutthroat yet. I guess too niche.

5
Vendor Discussion & Reviews / Who can I work with to design a carbon fork?
« on: June 20, 2024, 03:14:09 PM »
Basically what I want doesn’t exist or barely exists but is super expensive from a western brand. I want a Boost, flat mount, gravel fork with a ~400 A2C measurement, and clearance for 2.4” tire for a custom Ti frame I’m designing. There is the Curve Seek fork with 430mm A2C and the Bearclaw Ramhorn Boost fork with 41mm A2C, but both are over $600 USD. Does anyone know of a manufacturer who works with clients to design a custom carbon fork? Or perhaps knows who makes the Bearclaw or Curve forks? Thanks.

6
Component Deals & Selection / Welded-Seam Waterproof Frame Bag makers?
« on: September 07, 2023, 03:50:13 PM »
Does anyone know manufacturers of welded seam frame bags like those made by Apidura, Blackburn, Ortleib, etc? Looking to have some bags manufactured. Thanks

7
Cyclocross Frames, Wheels & Components / Adjustable offset carbon gravel fork?
« on: August 17, 2023, 10:49:23 AM »
I’ve seen this fork pop up on a couple of western sites. Here’s a couple examples:
https://www.brothercycles.com/shop/forks/brother-carbon-gravel-fork-v2/
https://landyachtzbikes.com/bike/ab-st-gravel-bike/


It has adjustable offset of 47/52mm and clearance for 700x50 tires. I’m wondering if anyone knows the OEM, or at least a cheap source to buy it direct from China? Thanks.

8
Component Deals & Selection / Fake eeWings titanium cranks
« on: May 01, 2023, 10:13:33 PM »
I just became aware of the counterfeit eeBrakes and eeWings available on AliExpress. Reports on the brakes are mostly positive. Has anyone tried, or heard of anyone trying the eeWings cranks?

US $395.99 | Handmade Titanium Crankset MTB Crank ARMS Immortal Ti Crank Mountain bike Crank arms Road Bike Crankset Titanium MTB Parts
https://a.aliexpress.com/_m0tPT52

9
Metal Frames / Custom Steel frames, like Waltly does with Titanuim?
« on: October 19, 2020, 12:20:29 AM »
Anyone know of a reputable steel frame builder who does one-off customs, similar to working with Waltly on a custom Ti bike? Nothing fancy like lugs, just TIG or brazed with my geometry and good tube sets & dropouts. Thanks!

Pages: [1]