Quote from: gf on September 18, 2025, 01:27:53 AM
Hello; I have the ssame frame with integrated handlebar included in the frame set.

Can you post a picture? Curious how it looks.


Also I originally had the same problem with cables being too long and resistance.

Here are some photos of my G058's integrated bars (from SPCycle, note the backsweep on the tops). They're 420mm wide with a 110mm stem. Frame is chameleon blue glossy.

Quote from: sukerbole1 on February 04, 2025, 02:24:02 PM
Build it up and rode a bit with it, will post proper pictures in future.

Components are
Tantan GR048 with custom paint (Red metallic, with the tops of bars being black, and matte varnish)
9Velo GV45 2.0 (already had them some months)
GRX820 (with GRX400 brakes)
RXL SL gravel bars at 42CM
Kocevlo stem at 90mm
Silca bar tape (Knockoff? of some ali seller, easily nicest bar tape ive used though)
Redshift grips (Knockoff of same ali seller, surprisingly great)

Can you make some close-up photos of bar and stem were cables go from bar to stem? How did you do the wiring? Where there any problems when doing the cables?

Thank you.

PSA to anyone ordering the integrated bars with their frameset: The "reach" measurement is from the end of the bars not the bar stem clamp area and due to back sweep the actual reach is like 15mm less or only 55mm, not the 69mm advertised. I learned that the hard way. Who wants handlebars with such a short reach?

I really would like this frame BUT with UDH and Downtube storage... why doesn't anybody make one? Perferably EPS and possibly even lighter? To much asked? 

Quote from: Rolle2k on November 18, 2025, 03:10:39 AM
I really would like this frame BUT with UDH and Downtube storage... why doesn't anybody make one? Perferably EPS and possibly even lighter? To much asked? 

CWind has this frame with a UDH but no downtube storage.  Their UDH model is called the G30U.  I actually somehow got a UDH on mine, too, even though it was the older design with partially internal cables.

Quote from: metachlone on October 30, 2025, 04:00:33 PM
Can you make some close-up photos of bar and stem were cables go from bar to stem? How did you do the wiring? Where there any problems when doing the cables?

Thank you.

Slow response, but anyway, its hard to make a picture because you can't really see it. I didn't route the cables through the bar (would be way too tight with 2 hydraulics hoses and 2 shifter cables), and then on the stem there's a little cap at the bottom you screw on. It definitely wasn't easy to get it on, it's still quite tight. Then they come down the steerer tube, and on a C spacer to go into the frame.

Still happy with my G058. Run it for a year including some deep bikepacking.

Wheeltop GEX and Elite carbon wheelset.

I have ridden also about a year and one bike packing trip to Norway. Had some serious speed wobble with pannier bags, fork mounts and bar bag. Since then I have made a rear rack mounting axle that goes thru the thru axle and made a stiffer upper rack attachment. Not tested yet. But this was the first time ever I had speed wobble. The frame is quite flexible.

I get a bit of speed wobble only when going no-hands, with bar bag, and above a certain speed. It's a bit annoying as on a long ride without stopping for an hour+, the occaisonal sitting up and stretching is valuable. But not a big deal overall.

Hey.

One question for g058 owners who run 1x chainring.

I have 36t 3mm offset (scenicx gr3 crankset) and 10-45t slx cassete and everything is ok. No chain noise. This is gravel setup.
For road setup, I've bought 42t offset 4,2 and there is chain noise in the 3 lightest gears (noise is on chainring), no noise on smaller cogs. And 42t is too big with this offset, only 1-2mm clearance to frame. So I can't go with bigger offset and have to change to smaller cog, hopefully 40t will be ok. The specs say, the largest chainring is 46t, but probably with no offset.

Does anyone run big chainring front and has no chain noise? The problem is probably wide BB.

Tnx