LTK266-D-SL, race frame, 680g, <800g w/paint & metal parts (M), fits 35mm+ tires

Started by Sakizashi, June 29, 2025, 12:36:26 AM

Previous topic - Next topic

dlul

Quote from: Takiyaki on November 12, 2026, 12:10:53 PMJust to confirm, these are 2x setups? Preferably electronic since those FDs are even bigger. I mean I guess I'm gonna find out in a week or so.

Sorry I run it 1by

Takiyaki

Quote from: fvega on November 14, 2026, 09:21:46 AM117 mm front, 168 mm rear 70 gm for both at about $15 on aliexpress. They are not the lightest but could not find anything significantly lighter that was not custom carbon axles for more than $100 at about 30 gm. It would be good if others post their weights and sources.
I got some random titanium thru axles from AE, but I just discovered they are heavier than whatever stock axles got sent with my FM639

I think if you can hit around ~70-80g for the pair you're fine.

Unrelated, would love to hear more about your build. Weight is impressive

pieter bevernage

Disappointed with the Long Teng Sports LTK266-D-SL – Serious Quality Concerns

I am extremely disappointed with the quality of my Long Teng Sports LTK266-D-SL carbon frame.

During inspection prior to assembly, I discovered several concerning defects:

A cavity approximately 2–3 mm deep inside the bottom bracket area.

Poor and irregular carbon finishing inside the seat tube.

Excessive play between the headset bearings and their bearing seats.

I am surprised that this frame passed the manufacturer's quality control.

I no longer have sufficient confidence in the safety of this frame to ride it.

Has anyone else experienced similar quality issues with Long Teng Sports frames?


Sakizashi

Quote from: pieter bevernage on November 19, 2026, 10:27:33 AMDisappointed with the Long Teng Sports LTK266-D-SL – Serious Quality Concerns

I am extremely disappointed with the quality of my Long Teng Sports LTK266-D-SL carbon frame.

During inspection prior to assembly, I discovered several concerning defects:

A cavity approximately 2–3 mm deep inside the bottom bracket area.

Poor and irregular carbon finishing inside the seat tube.

Excessive play between the headset bearings and their bearing seats.

I am surprised that this frame passed the manufacturer's quality control.

I no longer have sufficient confidence in the safety of this frame to ride it.

Has anyone else experienced similar quality issues with Long Teng Sports frames?

I believe the BB area you showed in the photo is where the patch is (where they remove internal structure). If that dark part is an actual hole, that seems like a big problem. The seat tube alone would be an issue for me. That's a lot of material missing from what I think is a load-bearing area. I'd push for an exchange based on the second issue alone.

The bearings are sort of a known issue — and I personally avoided them altogether and used an FSA headset.

pieter bevernage

I have already asked several times for either a refund or a replacement frame. I must say that Alisa has always been friendly and polite when responding to my emails. However, I am not satisfied with the response from Long Teng Sports.

They claim that these imperfections are completely within their quality standards, that the frame is perfectly safe to ride, and that any cracking or structural failure would be covered under warranty.

I replied that a warranty would be of little comfort to me if I ended up paralysed due to a structural failure of the frame.

Below is their latest response by email:
Each product will be have quality check before packing and I confirmed with our manager once again for you.

For the small holes on the inner wall of the tube and BB, they're not material missing. They're formed by air pressure before the resin fully cured during molding, they're the surface flaw and does not affect the structural strength. Totaly safe to ride, no worries. And the frame is fully monocoque construction, during the molding process, internal air pressure was introduced from the bottom of the BB shell, -- that's what causes the slight resin irregularity on the inner wall and the vent port at the cover. It's a normal by product of the internal blow molding process and doesn't affect structural integrity. There're the small holes on most the frames more or less, no necessary to repair them. I'll show you pictures of the other frameset which are ready for shipping later.

If you still mind them, you can use some AB epoxy to fill the holes, it will cure in 24-48 hours, no heat required, just leave it alone. But it's not necessary to do that.

Hillboy

Quote from: pieter bevernage on November 19, 2026, 10:27:33 AMDisappointed with the Long Teng Sports LTK266-D-SL – Serious Quality Concerns

I am extremely disappointed with the quality of my Long Teng Sports LTK266-D-SL carbon frame.

During inspection prior to assembly, I discovered several concerning defects:

A cavity approximately 2–3 mm deep inside the bottom bracket area.

Poor and irregular carbon finishing inside the seat tube.

Excessive play between the headset bearings and their bearing seats.

I am surprised that this frame passed the manufacturer's quality control.

I no longer have sufficient confidence in the safety of this frame to ride it.

Has anyone else experienced similar quality issues with Long Teng Sports frames?

I have also recently received this frame and it appears fine, but I'm still building.

I'm curious within the seatpost area are they actually voids with no resin? Or are they smooth?

The bottom bracket area, is that at the very bottom centre of the shell? If so, this area is where the bladders are inflated/removed to my understanding and later a small circular plug is inserted to fill this, along with resin. Mine has an obvious circular section about 15mm diameter but no resin overflow, this appears more raw carbon/matte colour. Is yours perhaps the same with just messy resin? Or is there a physical void that you can feel?

I'm happy to post some images if you let me know before tomorrow when I finish my build.

waltthizzney

Can anyone explain how to install the stock headset?

Does the small black washer base go under or over the lower head tube bearing?

Am I suppose to jam it down? I don't want to damage the carbon

Hillboy

Quote from: waltthizzney on <strong>Today</strong> at 12:11:23 PMCan anyone explain how to install the stock headset?

Does the small black washer base go under or over the lower head tube bearing?

Am I suppose to jam it down? I don't want to damage the carbon

I don't have the stock headset as opted for the FSA ACR low stack but on my build there is nothing else other than the bearing on the lowers side. The bearing just sits on the fork.