Lexon "Riot 10"

[uraberg]

Ztto 9-50t...no problems....only mistery o had to sort out was afterr changing it to my new fiberin carbon wheels. The cassete was never fully thightened even with the correct torque so i had To include a spacer( which was not suposedly needed as my driver is XD not XDR.

I actually had mine come undone as well. I now have it loctited , hopefully that will take care of it.

[Jotwoo]

I see the riot frame is not available anymore for new orders at the Lexon store and the everjoy store. Anybody knows what’s up?

[RongGearRob]

It looks like Everjoy is no longer selling Lexon bikes period.  Not sure what is up, but the Riot 10 is available through other AliExpress sellers  Toplevel Bike Stop and Ryet.

[RDY]

Can anyone confirm if the Lexon and Riot decals are above or below the clear?  Also what is rear travel with a 165*45?

[RongGearRob]

Looks like Everjoy is selling Lexon Riot 2022.  I haven't checked all of the specs but it seems to be very similar to the 2021 version, Riot 10, with the exception of allowing for a larger front chainring.  It now allows for up to a 40T chainring.  I think the Lexon decal on downtube might be new too, my Riot 10 frame is matte without any decals, so I can't be sure. 

[dan_cx]

 Any "average size" riders riding a Large/19" Riot? I'm wondering how short/cramped the cockpit feels, with such a short reach? I'm 5' 11"/1.8m tall, and pretty much fall in the textbook L/56cm frame category on 99% of bikes out there. Looking at the geometry chart, the reach is -28mm & the front center is -34mm shorter than my current Norco Revolver. It's also -21mm shorter wheelbase than the Norco. I'm concerned that there may also be an issue with toe-overlap on the front wheel. Has anyone run into this? I'm moving to 170mm cranks on all my mtbs, so maybe that 5mm difference will avoid any toe to wheel contact? I'll be running a 120mm fork, and there's only a 6mm difference in the crown to axle length - Riot's 520 vs my RS-1's 526 - so not much will change with the Riot's geometry there.

 If anyone's on a L/19". I'd appreciate your input & thoughts on the bike overall.

[RongGearRob]

I'm 6' and riding a large Riot, I find it fits me well and I do not feel cramped.  My previous bike was a Specialized Crave 2014 hard tail, the Riot is "bigger" in most aspects when compared to my old bike, 30mm longer reach (but I'm using a shorter stem now and wider bars) and the wheelbase especially is much longer (50mm) due to the slacker head tube. Earlier in this thread there are a bunch of comments on bike measurements which may be helpful to you.  In my opinion it seems Lexon is keeping with traditional sizing charts, whereas today many bike brands have increased the size of bikes, so what used to be a large is now considered a medium and so on.  All said at 6' I'm comfortable on the size large Riot, I don't feel cramped or stretched out and I'm using 175mm cranks.  Hope this helps.

[dan_cx]

@RongGearBob what's the wheelbase on your L build? Is that with the 100 or the 120 fork?

[marq3z]

Hi all, anybody knows the font used by LEXON ?? I wanna try to make some decals for my bike because i purchased matte one

[RongGearRob]

@RongGearBob what's the wheelbase on your L build? Is that with the 100 or the 120 fork?

My wheelbase on the size L frame with 120mm RS Reba is ~1193mm. 

[dan_cx]

My wheelbase on the size L frame with 120mm RS Reba is ~1193mm.

Awesome, thanks! My Norco sits at 1188mm and I was concerned that the Riot would be considerably shorter, based off its relatively small reach & TT numbers. Would hate to order & build one up just for it to be a squirrelly twitchy mess.

[saintrider]

Hi all, anybody knows the font used by LEXON ?? I wanna try to make some decals for my bike because i purchased matte one

Thats not the way to do it......

1. Find a nice quality image online of the logo.
2. Trace it using an image vectoring software like Adobe Illustrator.

[marq3z]

Thats not the way to do it......

1. Find a nice quality image online of the logo.
2. Trace it using an image vectoring software like Adobe Illustrator.

Yes, i know this way but its difficult to find good quality images. I have one also with logo and my friend will try to make it.
I asked also for this, if somebody has the vector of LEXON letters and the logo... Thanks in advance 

[RDY]

Just DM Lexon and ask them.

[dan_cx]

Hi all, anybody knows the font used by LEXON ?? I wanna try to make some decals for my bike because i purchased matte one

It's also the exact same font/graphic used by Ghost, for their "Riot" bike. I'd guess that Lexon just took that & used it after Ghost retired their model.