VeloBuild VB-R-268 frame

[Tdiguy]

@maliba

See below, lmk if you need a closer view-

[Freddy__HH]

@maliba

See below, lmk if you need a closer view-

Looking Good! Do you know the weight of it?

[EricL]

@maliba

See below, lmk if you need a closer view-

Hex ! Nice build. Where did you get your spacers ? It seems you did not use the ones provided by VB. Thanks

[Tdiguy]

Looking Good! Do you know the weight of it?

No saddle bag, bottles, computer, it’s 18.0lbs. Semi tank, could definitely get it a lil lighter.

Hex ! Nice build. Where did you get your spacers ? It seems you did not use the ones provided by VB. Thanks

Correct, it’s the spacer provided for the non “VB” bar.

[MALIBA]

No saddle bag, bottles, computer, it’s 18.0lbs. Semi tank, could definitely get it a lil lighter.
Correct, it’s the spacer provided for the non “VB” bar.

In this last photo it’s really easy to see. You used the full kit that comes with the handlebar and not a mix of the original cover + the spacers from the handlebar you used.

I wanted to know if it would be possible to use the original cover (which fits perfectly in that recessed area of the headset) together with the spacers from an alternative handlebar.

Maybe it could be possible by redoing a new cover via 3D printing.

Thanks for the photos!!

[Tdiguy]

In this last photo it’s really easy to see. You used the full kit that comes with the handlebar and not a mix of the original cover + the spacers from the handlebar you used.

I wanted to know if it would be possible to use the original cover (which fits perfectly in that recessed area of the headset) together with the spacers from an alternative handlebar.

Maybe it could be possible by redoing a new cover via 3D printing.

Thanks for the photos!!

I was hung up on wanting to use the supplied bearing cover since it has a clean and finished look. Howeve, it will not key into the supplied spacers. You’d have to do a 3d printed custom cover.

[gandalf]

In this last photo it’s really easy to see. You used the full kit that comes with the handlebar and not a mix of the original cover + the spacers from the handlebar you used.

I wanted to know if it would be possible to use the original cover (which fits perfectly in that recessed area of the headset) together with the spacers from an alternative handlebar.

Maybe it could be possible by redoing a new cover via 3D printing.

Thanks for the photos!!

I usted a ryet handlebar oth original cover. I think a had to sand a couple of pins (Sorry about my english) but it fits perfect y. I will post a pic tomorrow

[Tableware2851]

Hi guys, I just received my VB-268 today, but the packaging was badly damaged. I couldn't spot any cracks with my flashlight or hear any delamination when I tapped it with a coin. Do you think it's safe to ride?

[pavlo.k]

Hi guys, I just received my VB-268 today, but the packaging was badly damaged. I couldn't spot any cracks with my flashlight or hear any delamination when I tapped it with a coin. Do you think it's safe to ride?

Wouldn't ride that box if I were you

[Cnasta]

Wouldn't ride that box if I were you

Especially not in wet conditions!

[Tableware2851]

Haha, very funny guys.

Seriously though, I've checked the frame with a flashlight and the coin tap test and found nothing obvious. Any other DIY checks you'd recommend before I build it up, or specific high-stress areas on the 268 I should re-examine? Just want to be sure before I ride it.

[pavlo.k]

Haha, very funny guys.

Seriously though, I've checked the frame with a flashlight and the coin tap test and found nothing obvious. Any other DIY checks you'd recommend before I build it up, or specific high-stress areas on the 268 I should re-examine? Just want to be sure before I ride it.

Well, you didn't show the frame. Guesstimating the damage by the box, I'd say the frame should be good. It's just a corner from the looks of it.

[Tableware2851]

There are no visible cracks or other damage to the frame. I heard that a carbon frame can have compression damage that you can't see, so I asked. Thanks for the answer.

[Bodoman]

Hello everyone!
I'm trying to buy the 268 custom painted in icebreake red color, and I'm trying to get in contact with someone from there but no response after 5 days. I send the email to support@velobuild.com and chris@velobuild.com without success. Do you guys recommend some other way to contact them ?

Thank you !

[carboncal]

I was able to converse with them via WhatsApp